How To Set Up A Bed With Just A Headboard

Download Article

Download Article

Fitting a new headboard to your bed is a cinch. Floor-standing headboards and strutted headboards are both easily attached by screwing bolts through the headboard's struts and into the appropriate screw holes in your bed. Additionally, a popular alternative is to mountain the headboard to the wall instead of the bed.

1. 1

   Measure between screw holes before buying. Divan beds are designed as backless, but they ofttimes include screw holes for headboards to exist added later. Before purchasing a new headboard, cheque how far apart its struts need to be in order to fit your bed. Check the back of your bed for bolts or screw holes on either side and measure the distance between them.

   • Larger beds may accept more than ane pigsty in a vertical line, but measuring these aren't necessary. You desire the horizontal altitude from a pigsty toward one side of the bed to one that's level with it toward the other.
   • This step is not necessary if you lot plan to mountain your headboard to the wall.

2. 2

   Decide how wide your headboard should be. Commencement, measure from ane corner of its head to the other to find out its width. Side by side, decide if you lot want the headboard to back any surrounding article of furniture, such equally matching nightstands. If so, measure out the altitude betwixt the bed and those pieces' farthest sides. Add together those figures to your total width.

   • Headboards typically projection anywhere upwardly to three inches (7.6 cm) by the corner of the bed'due south head.^[1]
   • If you are backing other furniture also, apply this dominion to their farthest sides from the bed.

   Advertisement

3. 3

   Determine how high it should exist. Measure the length of the bed, from its head to its pes. Also mensurate its height, including the mattress and whatever toppers. Utilise these figures to determine how high above the top of your mattress your headboard should rising.^[2]

   • Standard headboards stand roughly 14 inches (35.5 cm) higher than the superlative of the mattress.
   • Extra tall headboards should be less than the bed's length.

Advertisement

1. 1

   Find your divan'south screw holes. Check its dorsum of the divan for two holes, one toward either side. Wait where each is near often found, inside three to four inches (seven to ten cm) of both the side corner and the height of the frame. With cloth-covered frames, experience with your mitt for the holes if the fabric'south pattern makes them difficult to spot.

   • Well-nigh simply not all frames will already have bolts screwed into place, which makes finding the holes easier.
   • Larger beds may have more than one screw pigsty in a vertical line in order to support larger, heavier headboards.

2. 2

   Screw the struts to the frame. If your frame already has bolts in place, remove them. Then line up the headboard's struts with the frame'due south screw holes. Insert a bolt through the gap in each strut and screw it into the spiral hole. Begin tightening the bolt to the frame, only stop curt of tightening it all the way to the betoken of immobilizing the headboard.

   • Having ane or more partners to concur the headboard steady is advisable. Headboards with struts will exist particularly top-heavy and could fall over while you lot work.
   • If your bed frame does not include bolts, contact the manufacturer to inquire which size is required so you tin can purchase them separately.

3. iii

   Adjust the headboard to your desired superlative. Identify your mattress on the frame then you tin meliorate judge how high you want your headboard to exist. Raise or lower the headboard along its struts. If needed, loosen the bolts so you can do so more easily. In one case you lot decide how high or low yous wish it to be, use a level to ostend that both sides are raised equally loftier. Then tighten the bolts all the way to secure the headboard in place.

   • In addition to your mattress, add together any other materials that might add peak to it, such equally cream toppers or electric sheets.
   • Having partner(s) to enhance and lower the headboard volition enable yous to stand dorsum and judge its top with less fuss.

Ad

1. 1

   Start off as you would with struts. Locate the screw holes in the back of the bed'south head. If you lot notice bolts there, remove them. If not, purchase bolts of the appropriate size for the holes yous find.

   • Floor-continuing headboards and those with struts are installed in about identical fashion.

2. ii

   Stand the headboard in place. Notation that the struts to a floor-standing headboard are built into the headboard itself. This is the bottom end. Position the headboard upright backside the frame's caput. Line the struts up with the screw holes in the frame. Keep the bottom of the headboard flush on the floor.

   • The chief difference between floor-continuing headboards and those with struts is in the name: floor-standing headboards should do just that. Don't adjust the tiptop every bit you lot would with elementary struts.

3. 3

   Secure the headboard. Fit a bolt through the gap in each strut. Screw it into the corresponding screw hole.^[three] Tighten information technology all the manner so the headboard becomes firmly fastened to the frame.

   • Take a partner agree the headboard upwards so it remains flush confronting the bed frame every bit y'all work.

Advertisement

1. 1

   Mensurate and mark. Showtime, decide exactly how high the headboard should be from the floor. Side by side, measure the height of the headboard itself to determine where the headboard cleat needs to be installed. Then mark the post-obit measurements in pencil on the wall:^[four]

   • The height of the headboard'southward bottom from the floor.
   • The height of its top from the floor.
   • A 4th of the way downward from its top (for the cleat).

2. two

   Find and mark studs. Employ a stud-finder to locate studs behind the wall in the area where the headboard will be mounted. For a single cleat, find two consecutive studs that are closest to the centre of your bed. Marking each one'south location with pencil on the wall at the height of your third measurement (a fourth of the way down from the peak of headboard).^[5]

   • Always mount your cleat to studs, even if it isn't perfectly centered over your bed. A slightly off-center cleat mounted to studs will exist stronger than a perfectly centered cleat attached to drywall.
   • King-size headboards require two cleats. In this example, find iv consecutive studs that are closest to your bed's centre.
   • Standard spacing betwixt studs is 16" (41 cm).

3. 3

   Install and measure out the cleat. Screw the cleat into the studs. Examination to make certain it is secure and immobile. Then measure from the bottom of the cleat to where the lesser of the headboard will be once mounted.^[half-dozen]

   • Ever examination the cleat before hanging your headboard to make sure information technology is stiff enough to support its weight.

4. 4

   Adhere the cleat plate to the headboard. To discover out where to attach the cleat plate, refer to your instructions, since the size of the cleat and plate may vary by brand or model. Determine exactly how much height to add to your previous measurement. Then marking the back of your headboard at this new height.^[7]

   • Brand sure the placement of your marks on the headboard align with the cleat on the wall.
   • The cleat plate on the back of the headboard should fit directly over the installed cleat.

5. five

   Hang and secure your headboard. First, mount your headboard past lifting its cleat plate up and over the installed cleat so it fits between that and the wall. Side by side, use your stud-finder to locate two new studs behind the headboard, 1 on each side, nearest to either end. Support the headboard from the bottom by installing an angle atomic number 26 in each stud. Refer to your cleat's instructions for the recommended size atomic number 26.^[eight]

   • Too check for recommendations most attaching spacers toward the lesser of the headboard's back. The cleat may cause the headboard to projection from the wall toward the top. Spacers toward the lesser will keep the headboard straight. The recommended size may vary by brand or model.

Advertisement

Add together New Question

• Question

  How practice yous make a elementary wooden headboard?

  

  David Julien is a DIY Specialist and the Principal Possessor at Prissy DIY based in Quebec, Canada. David specializes in creating plans to make unique, affordable, and modern home furnishings. He holds a BA in Graphic Design from the University of Quebec Outaouais. Squeamish DIY uses sustainable and high-quality materials to create products that are simple to make for anybody.

  

  DIY Specialist

  Expert Answer

  Buying a new headboard can be expensive. Luckily there is some other way to renew your bed at a lower cost. Pace 1: Purchase a desk summit/ plywood. You lot can find them in dissimilar sizes and colors in article of furniture stores. Stride 2: Cut the board to the tiptop yous want your headboard to be. Step 3: Screw the new headboard straight onto the onetime i from behind so you can't see the screws. Choice: For optimal comfort, install the board at an angle.

• Question

  The screws are likewise long and are scratching up the wall! What can I do?

  

  Either replace them with shorter screws or attach pasty felt pads to the ends as a barrier between them and the wall.

• Question

  I institute a headboard without screws, just a big nickel-sized pigsty on the lesser of each side; can that be stable?

  

  If you secure to a wall stud instead of the bed, information technology should exist fine.

• Question

  How can I attach a headboard to a bed frame if in that location are no holes within the headboard?

  

  Mount it to the wall instead.

• Question

  How far should a headboard stick out from the side of the bed?

  

  The standard is between 0 and 3 inches from either side.

• Question

  Can you put an end board on a divan?

  

  Many divans have spiral holes at both the head and the human foot of the bed so both headboards and finish boards can be added.

Enquire a Question

200 characters left

Include your electronic mail address to go a message when this question is answered.

Submit

Ad

• Observe the screw holes in your bed and measure the altitude between them before purchasing a new headboard. Make sure the headboard's struts line up before bringing it dwelling house.

• If the spacing of your headboard's struts don't friction match the screw holes, try securing it to the wall's studs instead.

Advertisement

Things You'll Need

For struts and flooring-standing headboards:

• Screwdriver
• Partner

For wall-mounting:

• Headboard cleat(s) and cleat plate(southward)
• Measuring tape
• Pencil
• Stud-finder
• Drill or screwdriver
• Angle irons
• Spacer(southward)

Well-nigh This Article

Article Summary X

If you haven't bought a headboard yet, y'all'll need one that's the same width every bit your bed and at least 3 inches taller than your bed so it will properly attach. If y'all already have a headboard that doesn't fit, you can screw it into the wall behind your bed instead. To mount a headboard to a bed, you'll need to spiral headboard struts to your bed frame. Then, you tin place the headboard at the superlative you desire and tighten the bolts to hold it in place. To mount a headboard to the wall, first, you'll need to mark where on the wall you want it to be. And so you'll demand to screw a cleat board into the wall where the height of the headboard will gear up. Then, hang the headboard onto the cleat. To learn how to install a floor-standing headboard, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 292,133 times.

Did this commodity help yous?

Source: https://www.wikihow.com/Fit-a-Bed-Headboard

Share this post